Uusimmat viitteet

  • Concept design of composite axis for Cencorp high-speed odd-form component placing machine 

    Palomäki, Eetu (Saimaan ammattikorkeakoulu, 2018)
    The purpose of this thesis was to study the possibilities of creating a lighter design of an axis system for a new high-speed odd-form component placing machine. The mass reduction possibilities were mainly studied by ...
  • Vibration analysis of shaft in SolidWorks and ANSYS 

    Grunwald, Benjamin (Saimaan ammattikorkeakoulu, 2018)
    The objective of this thesis was to explore the differences in use of a professional FEM-Software and a FEM-Simulation-Tool that is integrated in a 3D-Design software. The study was commissioned by Seppo Toivanen of Saimaa ...
  • Flexible body tutorial for Mevea real-time simulation software 

    Nikitina, Anna (Saimaan ammattikorkeakoulu, 2018)
    The main goal of this study was to develop a tutorial about creation of flexible bodies in Mevea real-time simulation software. The work was commissioned by Mevea Ltd. Various sources were used to collect the data for ...
  • Automated production line of detergents 

    Rumiantcev, Roman (Saimaan ammattikorkeakoulu, 2017)
    The main aim of this study was to identify and analyze the constraints which occur while designing a production line and to develop a production line for detergents which would fulfill both the constraints and the requests ...
  • The design, construction and implementation of an autonomous outdoor quadcopter using an RPi microcomputer and a MultiWii flight controller 

    Guliaev, Nikita (Saimaan ammattikorkeakoulu, 2017)
    The purpose of the present study was to design and construct an outdoor aerial vehicle, called a quadcopter, with autonomous flight functions, and to install within the vehicle a video streaming system. The thesis also ...
  • Comparison of 3D modeling software 

    Bobylev, Denis (Saimaan ammattikorkeakoulu, 2017)
    The purpose of the study was to do a research and get knowledge about three different 3D modeling Softwares and to figure out the best option for a Mechanical Engineering student at Saimaa University of Applied Sciences ...
  • Barrier free main entrance arrangement in the renovation of residential house in Saint-Petersburg 

    Bakaeva, Liubov (Saimaan ammattikorkeakoulu, 2017)
    The aim of this work was to observe regulations connected with renovation of public buildings, understand how demands of reduced mobility persons affect to the architectural concepts. And to design a project of real ...
  • Certification of products in NCC 

    Beznosikova, Daria (Saimaan ammattikorkeakoulu, 2017)
    The study was commissioned by NCC Real Estate to understand and compile a single table of all the required mandatory certificates required for the delivery of the NCC residential complex of Swedish Krona in commission. ...
  • Four axis hot-wire foam cutter controlled by Mindstorms EV3 

    Ivanovskis, Luka (Saimaan ammattikorkeakoulu, 2017)
    The purpose of the study was to develop a 4-axis numerically controlled hot-wire foam cutter suitable for flying aircraft modelling purposes. Numerically controlled foam cutter had to be able to cut intricate shapes out ...
  • Features of selection of flow measurement methods and devices for flow measuring of liquefied petroleum gas in pipelines 

    Ustinov, Stanislav (Saimaan ammattikorkeakoulu, 2016)
    The purpose for the study was to get more knowledge about fluid and gases flow measurement methods and devices and to analyse these methods as well as to identify the advantages and disadvantages of each method for different ...
  • Design of hydraulic scissors lifting platform 

    Olenin, Georgy (Saimaan ammattikorkeakoulu, 2016)
    The goal of this study was to apply the knowledge obtained from studying in the university and solve the substantial task of creating a design of the hydraulic scissors lifting platform. For this purpose a research of ...
  • Strength analysis of copper gas pipeline span 

    Ianevski, Philipp (Saimaan ammattikorkeakoulu, 2016)
    The purpose of the study was to analyze the stresses in a gas pipeline. While analyzing piping systems located inside building were used. Calculation of the strength of a gas pipeline is done by using information of the ...
  • 3D printing: technology and processing 

    Kurinov, Ilya (Saimaan ammattikorkeakoulu, 2016)
    The objective of the research was to improve the process of 3D printing on the laboratory machine. In the study processes of designing, printing and post-print-ing treatment were improved. The study was commissioned by ...
  • Accelerated improvement workshop in WP4004 program AIRBUS A330 by DMAIC method 

    Sadki, Fayçal (Saimaan ammattikorkeakoulu, 2016)
    The goal of this accelerated improvement project was to optimize the use of the jig boards in the program Airbus330-WP4004 production lines, decrease the spending on the making and equipping the jig board templates and ...
  • Analysis of electrodynamic brake for utilization in systems with rotating shafts 

    Sokolov, Georgii (Saimaan ammattikorkeakoulu, 2016)
    The goal of this study was to conduct an analysis of an opportunity to apply eddy current brakes in dynamical systems containing rotating shafts. While conducting the research the general principles of deceleration, eddy ...

Näytä lisää