Theseus - Selaus asiasanan mukaan "electronics"
Viitteet 61-80 / 87
-
Porting and Optimization of Kvaser CANopen Stack for STM32 Microcontrollers
(2024)This bachelor thesis, conducted within the Bachelor of Information Technology program, focuses on the development of a Hardware Abstraction Layer (HAL) for the STM32 platform, tailored specifically for integrating the ... -
Power Consumption Optimization and Measurement
(2021)The project aimed to design a system that consumed power as optimized as possible. The main components of the system included two Xbees, an Arduino Micro; otherwise, there were also an LED and a resistor that supported the ... -
Precise Positioning Concept and NTRIP Base Station
(2019)The purpose of this project is to discuss basic idea of precise satellite positioning. When it comes to positioning area, GPS has been acknowledged to be the most popular concept. However, positioning signal is not simple ... -
Prevention of EMI in the CAN bus systems of electric mining vehicles
(2023)Tämän opinnäytetyön aiheena oli sähkömagneettiset häiriöt Normetin sähkökäyttöisten kaivosajoneuvojen CAN-väyläjärjestelmissä. Tavoitteena oli vähentää häiriöstä aiheutuvia ongelmia muodostamalla yhteiset periaatteet ...Rajattu käyttöoikeus / Restricted access / Tillgången är begränsad -
Printed electronics ECAD design and simulation
(2022)Painettu elektroniikka poikkeaa paljon perinteisen elektroniikan suunnittelusta ja valmistuksesta, missä on jo olemassa paljon erilaisia standardisoituja suunnittelu ja valmistusmenetelmiä. Painetussa elektroniikassa ...Rajattu käyttöoikeus / Restricted access / Tillgången är begränsad -
Printed Electronics: Capabilities and Potentials for Intelligent Interactive Packaging
(2022)Printed Electronics as an emerging technology is a fast-evolving disruptive and enabling innovative technology that utilizes functional inks and conventional printing techniques for the mass production of flexible and ... -
Programmable Boost Controller
(2023)This research centers on the development of a programmable boost controller, a device to effectively regulate the intake air pressure within a turbocharged internal combustion engine. The purpose of this study was to ... -
PWM Driven LEDs Based on Isolated DC Voltage Measurement
(2023)Voltage regulated LED driver ICs are commonly used to drive LEDs in variable voltage conditions. The purpose of this thesis work was to design an LED driving circuit without using LED driver ICs for Teknoware company. A ... -
Racing vehicle wiring harness design
(2022)The purpose of this thesis was to design the wiring harness for Elmer Racing’s er8 GT Time Attack racing vehicle. Work began with defining the specifications for the wiring harness and choosing the components which could ... -
Review of Data Converters
(2021)The goal of this report is to review different types of electronic data converters developed till now. The report also goes through working and characteristics of those converters in brief. To support the review, a ... -
Screen Printed Circuits for Fiber-Reinforced Polymer Pultrusion
(2022)There is very little literature on multifunctional composites, also known as "smart composites," made with printed electronics and pultrusion. Therefore, the primary goal of this thesis was to demonstrate the viability of ...Rajattu käyttöoikeus / Restricted access / Tillgången är begränsad -
Smart Weather Station
(2021)The biggest role of my project is to make a device that can gauge the temperature or the humidity of gardens or farms using sensors scattered all around them. Furthermore, the fundamental objective was to make a program ... -
Step-Down Switching Regulator Design
(2022)The goal of the thesis project was to design two different step-down switching regulators which would be measured for their line and load regulation. EMC measurement was also done for the PCBs since switching regulators ... -
Study of Cozify Hub 868MHz Radio Receiver
(2022)The thesis work was a part of a project at Cozify in where the Cozify smart hub’s generic 868MHz radio FM-receiving capabilities and performance were investigated. Topic was brought out when commercializing, a new device ... -
Study on Communication Protocols Modbus and CAN Bus
(2023)Tässä opinnäytetyössä tutkitaan Modbus- ja CAN-väylän standardeja. Nämä kaksi kenttäväylän protokollaan on laajasta käytössä eri sovellusalueilla. Modbus on yleinen teollisuussovellluksissa ja CAN-väylä autoteollisuudess ... -
Technical Search and Rescue Camera Rotation Circuit Segment Redesign Process Study
(2023)Savox Communications underwent a technical review for their SearchCam 3000 product that included the possibility of redesigning the product’s schematics in a way that excluded a difficult to source component without altering ... -
Test Automation for Timing of Modbus Protocol Extension
(2023)A communication protocol used for data transmission between devices represents the key element of industrial systems. Modbus is one of the oldest industrial communication protocols that is still widely used in automation ... -
The impact of product review videos on electronics consumers
(2024)Electronic products are becoming an indispensable part of people's lives. But most people only know how to use electronic products, they do not understand the specific value of them. At this point, some consumers will look ... -
Thrust Meter Error Analysis
(2021)This study examines measurement error of a device which measures model rocket motor thrust. This measurement device is designed as a personal project, and it will be used to test performance and consistency of model rocket ... -
Timer-Controlled 5 A Constant Current Source
(2021)The main objective of this project was to build a constant current source with a 5 A output. The project expectation was to create a power source capable of delivering high current output, generating the necessary thermal ...
















