"automaatio" - Selaus asiasanan mukaan Opinnäytetyöt (Avoin kokoelma)

    • Belysningsstyrningar med KNX : projektering, design och programmering 

      Sundqvist, Dennis (Yrkeshögskolan Novia, 2011)
      Detta examensarbete handlar om styrning av belysning i en större fastighet med hjälp av fastighetsautomationssystemet KNX. Dokumentet innehåller information om KNX angående dess styr- och övervakningsmöjligheter samt inom ...
    • Challenges and Opportunities with Digital Transformation in the Public Service : A case study in the Secretary Services in Vaasa 

      Kangas, Therese (2024)
      The objective of the thesis was to explore the challenges and opportunities facing the public sector due to the increased pace of digital transformation, with a specific focus on the initial stage of deconstruction of tasks ...
    • Development of Synchronization Tester and IEC Safety Standard Compliance 

      Johansson, Robin (2024)
      Detta examensarbete skrevs för ABB Energy Industries-avdelningen i Vasa, Finland. Examenarbetet underlättar viktig testning av kontrollsystem som utförs inom området för Factory Acceptance Testing (FAT). Synkronisering ...
    • Hydro Turbine Governor Test Platform with ABB System 800xA 

      Vikström, Johannes (2023)
      This bachelor’s thesis was commissioned by ABB Energy Industries division. The objective of the research is to determine the feasibility of using a virtual testing computer as a testing platform for FAT and SAT of ABB’s ...
    • Implementering av datainsamling för packningsmaskin 

      Nygård, Nikolai (2024)
      Detta examensarbete har utförts åt företaget Oy Prevex Ab. Syftet med detta examensarbete var att få samla in data om två packningsmaskiner. Detta har en fördel för företaget eftersom den insamlade informationen ger en ...
    • Integration testing of protection relays 

      Lehtosaari, Mattias (Yrkeshögskolan Novia, 2011)
      This Bachelor’s thesis has been made for the research and development department at ABB Oy, Distribution Automation. The purpose of Distribution Automation products is to improve the safety, the reliability and the performance ...
    • Isochronous Load Sharing Setup at STH - HUB 

      Malm, Kristoffer (2023)
      At STH in Vasklot, eight test cells have been built for testing customer engines and for research and development purposes. To have solutions ready for special tests in the future, Wärtsilä wanted to have a system installed, ...
    • Planering och installation av styrutrustning för dieselgenerator 

      Alho, André (Yrkeshögskolan Novia, 2012)
      Syftet med detta examensarbete var att försätta en begagnad dieselgeneratorenhet i driftskick genom att förnya el och styrutrustningen. Förutom planering och installation av moderniserad automatiklösning, skulle enheten ...
    • Rapid Prototyping Systems In Wärtsilä Laboratory 

      Birell, Tobias (Yrkeshögskolan Novia, 2012)
      Abstract This Bachelor’s thesis was commissioned by Wärtsilä Finland Oyj Engine Laboratory in Vaasa. The goal of the thesis was to get a wider understanding of the rapid prototyping unit on a Wärtsilä 20 engine and to ...
    • RTU 560 with IEC 61850 : Vaasa Engineering Oy 

      Ainasoja, Joakim (Yrkeshögskolan Novia, 2010)
      This thesis work was made in cooperation with Vaasa Engineering Oy. The thesis deals with the procedure for a configuration of an ABB RTU 560G for communication with protective relays from ABB and VAMP to a network control ...
    • Utveckling av testsystem för säkerhetsautomationssystem i kraftvärmeverk 

      Ahlvik, Marcus (Yrkeshögskolan Novia, 2012)
      Detta examensarbete har gjorts på uppdrag av Vaasa Enginering Oy. Examensarbetet omfattar utveckling av programvaran till ett testsystem för fabrikstest av säkerhetsautomationsenheter. Syftet med arbetet är att uppdragsgivaren ...
    • Utvärdering av maskinstyrning 

      Åbacka, Tommy (Yrkeshögskolan Novia, 2011)
      Arbetet gjordes åt Ab Ostromap Oy och behandlar maskinstyrning inom jordbyggnadsbranschen och dess olika områden. Syftet med arbetet var att undersöka hur ett maskinstyrningssystem är uppbyggt och hur man går till väga vid ...