KoulutusalaYrkeshögskolan NoviaSähkötekniikka

Viitteet 21-40 / 184

    • CE Marking Procedure for the Generating Set 

      Lillhannus, Diana (Yrkeshögskolan Novia, 2018)
      The purpose with this thesis is to be able to have the full understanding about the application and affixing of the CE mark on the generating set for the Marine Industry. This Bachelor’s thesis was produced for Wärtsilä, ...

    • Cold startup behavior of natural ester based transformer dielectric liquids 

      Knuts, Niklas (Yrkeshögskolan Novia, 2014)
      The use of a dielectric insulating liquid in an environment where it would solidify, may pose a problem in transformers equipped with conservators as the solidified liquid could block the piping to the conservator, resulting ...

    • Comparison of methods to measure torsional vibration 

      Holm, Jonas (Yrkeshögskolan Novia, 2014)
      Detta ingenjörsarbete är gjort för Wärtsilä Finlands motorlaboratorium i Vasa under vintern 2013 till 2014. Uppgiften med detta arbete var att jämföra två olika mätmetoder för att mäta torsionsvibrationer i en kamaxel. Den ...

    • Control Process: Development of an Arduino-Based Simulation and Interface System for NOVIA University of Applied Sciences 

      Llobera, Albert (2024)
      This thesis outlines the creation and implementation of an Arduino-based simulation tool designed to enhance the practical training of control systems for engineering students at NOVIA University. Given the complex nature ...

    • Cubicle Templates with Design Tool E3 

      Skrifvars, Kristoffer (Yrkeshögskolan Novia, 2015)
      This Bachelor’s thesis was commissioned by ABB Power Systems in Vaasa, Finland. They were at the time carrying out a transition into a new dynamical engineering tool called E3. The design tool had not been implemented among ...

    • Current Carrying Capacity Calculations for High and Medium Voltage Cables 

      Sundqvist, William Anders (2022)
      When sizing cables for a particular installation it is essential to find the current rating of those cables in their thermal environment. Cables will heat up as a result of the imposed current in the system. The cables can ...

    • Design and Construction of Chemical Ageing Test Rig 

      Kim, Norrgård (2019)
      This thesis has been made for Engine automation testing at Wärtsilä in Vaasa. Engine automation testing has a chemical aging test rig at Wärtsilä in Vaskiluoto. The rig has to be updated because of the poor temperature ...

    • Design av belastningstestapplikation för MIRKA® DEROS 5650CV slipmaskin 

      Staffans, Jakob (Yrkeshögskolan Novia, 2015)
      Detta examensarbete gjordes åt Power Tools avdelningen på KWH Mirka Ab. Målet var att skapa en belastningstestapplikation för elslipmaskiner för att enkelt och definitivt kontrollera maskinernas arbetstemperaturer. ...

    • Design control and protection for medium voltage switchgear 

      Nylund, Carl-Johan (Yrkeshögskolan Novia, 2012)
      This thesis has been made for the Plant department at Wärtsilä in Vaskiluoto, Vaasa. Wärtsilä in Vaskiluoto is an engine laboratory. The engine laboratory tests different engines before they are put in the engine portfolio. ...

    • Design of a High-speed Permanent Magnet Synchronous Generator for a Wind Turbine 

      Mukhtar, Syed Danish (2022)
      This thesis focuses on the enhancement of the performance efficiency generated by the High-speed Permanent Magnet Synchronous Generator (HSPMSG) due to brushless slip rings and high-power densities. It especially accounts ...

    • Designoptimering av lågspänningsställverk 

      Palmberg, Jesse (Yrkeshögskolan Novia, 2014)
      Abstrakt Detta examensarbete gjordes på uppdrag av diesel- och gaskraftverksavdelning på VEO Oy. Examensarbetet omfattar en utveckling av elplaneringen av lågspänningsställverk till diesel- och gaskraftverk. Elplaneringsverktyget ...

    • Development and Implementation of a Test Sequence for a Functional Tester 

      Erikslund, Petter (Yrkeshögskolan Novia, 2017)
      The purpose of this thesis is to develop and implement a test sequence for a final functional tester. The assignment was commissioned by Ampner Oy. The company produces products and services such as solutions for connecting ...

    • Development of a Design Master Tool for Upcoming Wärtsilä Engines 

      Öster, Daniel (Yrkeshögskolan Novia, 2015)
      Detta examensarbete gjordes åt Wärtsilä på avdelningen Ship Power Engines, Research & Development i Vasa. Målet med arbetet var att skapa ett designverktyg för att underlätta och förenkla genereringen av partitioneringslistor. ...

    • Development of Control Panel Cost Calculation Tool 

      Bäck, Tony (Yrkeshögskolan Novia, 2017)
      This Bachelor’s thesis consists of a cost calculation tool for control panels to power plants. The cost calculation tool shows material costs and makes needed material lists for the control panels. Commissioner for the ...

    • Development of E3 training material 

      Damlin, Kristian (2021)
      This thesis was done for the Industrial Automation and Energy Industries department at ABB. The main objective of this thesis was to develop E3 training material for new ABB colleagues. E3 is an electrical design software ...

    • Development of templates for protective relays in design tool E3 

      Lindfors, Axel (Yrkeshögskolan Novia, 2014)
      This Bachelor’s thesis work was done for ABB Power Generation Systems in Vaasa. The objective of this thesis work was to create ready-made templates in design tool E3, containing all key schematics associated with a ...

    • Digitalization for Optimization : Smart Grid operations in Finland 

      Niranjan, Rishab (2019)
      The following thesis examines the application of digitalized smart grid platforms for optimization in a utility network in Finland. The aim of the thesis is to assess and establish the usefulness of digitalization in a ...

    • Dimensionering av elstationers jordningssystem 

      Sjöblom, Jesper (Yrkeshögskolan Novia, 2018)
      Examensarbetet omfattar en beräkningskalkyl för elstationens jordningssystem. Beräkningskalkylen beräknar dimensioner för jordelektrod och jordledare samt om beröringsspänningen uppfyller kraven. Uppdragsgivare för arbetet ...

    • Dimensionering av mellanspänningskablar 

      Östman, Victor (2024)
      Syftet med detta examensarbete var att utveckla ett verktyg för dimensioneringen av mellanspänningskablar. Bestämmandet av storleken för denna typ av kabel är ett arbete som kräver noggranna beräkningar baserade på ...

    • Dimensioning of electrical installations : calculation softwares examined 

      Lindstedt, Mats (Yrkeshögskolan Novia, 2011)
      This thesis is an examination of calculation softwares for the dimensioning of electrical installations. The thesis is done in cooperation with Vaasa Engineering Oy. The goal is to help the employer find a calculation ...