KUNNONVALVONTATYÖKALUJEN KEHITTÄMINEN
Mäkinen, Laura (2011)
Mäkinen, Laura
Jyväskylän ammattikorkeakoulu
2011
All rights reserved
Julkaisun pysyvä osoite on
https://urn.fi/URN:NBN:fi:amk-201105239186
https://urn.fi/URN:NBN:fi:amk-201105239186
Tiivistelmä
Opinnäytetyön tavoitteena oli kehittää Savcor Wedge - tiedonkeruujärjestelmän työkaluja
automaatiokunnossapidon tarpeisiin UPM-Kymmene Oyj:n Jokilaakson tehtailla. Savcor Wedge on
prosessidatan hallintaan ja prosessivaihteluiden analysointiin tarkoitettu ohjelmistotyökalu.
Tavoitteena on luoda helppokäyttöiset ja selkeät käyttöliittymät, joita peruskäyttäjänkin on helppo
ymmärtää. Kehittämiskohteiksi on valittu kapasiteetti- ja yleistettävyyssyistä Jämsänkosken
paperikone 4:n (PK4) puristinosa ja paperikone 6:n (PK6) rullain. PK4:n alueella on mahdollisuus
nopeaan mittausdataan on-line 100 millisekunnin tasolla ja PK6:n alueella 200 millisekunnin tasolla
sekä 10 millisekunnin tasolla. Työn tuloksia on tarkoitus monistaa mahdollisuuksien mukaan myös
muille konelinjoille.
Työn alussa kartoitettiin jo olemassa olevia ja uusia ideoita haastattelemalla tehtaan omien
automaatioasentajien ja operaattoreiden lisäksi myös muiden UPM:n tehtaiden kunnossapitoosaajia.
Haastattelujen pohjalta poimittiin parhaat ideat, joita lähdettiin toteuttamaan.
Työn tuloksena PK4:n puristinosalle ja PK6:n rullaimelle luotiin taustatarkkailukaaviot, joilla
pystytään mm. valvomaan puristimen ja rullaimen liikeaikoja jatkuva-aikaisesti. Muita seurattavia
kohteita ovat säätimien lähtöjen ja säädettävien suureiden suhteen seuranta ja yksittäisten
suureiden seuranta.
The aim of this study was to develop Savcor Wedge process diagnostic system to correspond to the
needs of automation maintenance department. Savcor Wedge is a tool for process data handling
and process fluctuation analyses. The aim is to create user interfaces which have a clear
appearance and which are easy to use for a basic user. The press section of the paper machine 4
(PM4) and the reel of the paper machine 6 (PM6) were chosen to this work because of capacity
and generalizability reasons. At the PM4 there is possibility to use measurement data on-line up to
100 ms and at the PM6 up to 200 ms and 10ms. The results of this study are supposed to be used
also at the other machine lines if possible.
In the beginning new and already existing ideas were collected by interviewing the faculty of
Jämsä River mills in the automation department and operators at the PM4 and PM6. There were
interviews made also to the other UPM paper mill’s experts of condition monitoring. From these
interviews the best ideas were selected to develop during this study. As a result a background
monitoring schemas were created to the PM4 press section and PM6 reel to monitor on-line for
example the motion times of the press section and the reel. Other examples of the monitoring
targets are to monitor the ratio between the controller output and measured variable and to
monitor the single variables.
automaatiokunnossapidon tarpeisiin UPM-Kymmene Oyj:n Jokilaakson tehtailla. Savcor Wedge on
prosessidatan hallintaan ja prosessivaihteluiden analysointiin tarkoitettu ohjelmistotyökalu.
Tavoitteena on luoda helppokäyttöiset ja selkeät käyttöliittymät, joita peruskäyttäjänkin on helppo
ymmärtää. Kehittämiskohteiksi on valittu kapasiteetti- ja yleistettävyyssyistä Jämsänkosken
paperikone 4:n (PK4) puristinosa ja paperikone 6:n (PK6) rullain. PK4:n alueella on mahdollisuus
nopeaan mittausdataan on-line 100 millisekunnin tasolla ja PK6:n alueella 200 millisekunnin tasolla
sekä 10 millisekunnin tasolla. Työn tuloksia on tarkoitus monistaa mahdollisuuksien mukaan myös
muille konelinjoille.
Työn alussa kartoitettiin jo olemassa olevia ja uusia ideoita haastattelemalla tehtaan omien
automaatioasentajien ja operaattoreiden lisäksi myös muiden UPM:n tehtaiden kunnossapitoosaajia.
Haastattelujen pohjalta poimittiin parhaat ideat, joita lähdettiin toteuttamaan.
Työn tuloksena PK4:n puristinosalle ja PK6:n rullaimelle luotiin taustatarkkailukaaviot, joilla
pystytään mm. valvomaan puristimen ja rullaimen liikeaikoja jatkuva-aikaisesti. Muita seurattavia
kohteita ovat säätimien lähtöjen ja säädettävien suureiden suhteen seuranta ja yksittäisten
suureiden seuranta.
The aim of this study was to develop Savcor Wedge process diagnostic system to correspond to the
needs of automation maintenance department. Savcor Wedge is a tool for process data handling
and process fluctuation analyses. The aim is to create user interfaces which have a clear
appearance and which are easy to use for a basic user. The press section of the paper machine 4
(PM4) and the reel of the paper machine 6 (PM6) were chosen to this work because of capacity
and generalizability reasons. At the PM4 there is possibility to use measurement data on-line up to
100 ms and at the PM6 up to 200 ms and 10ms. The results of this study are supposed to be used
also at the other machine lines if possible.
In the beginning new and already existing ideas were collected by interviewing the faculty of
Jämsä River mills in the automation department and operators at the PM4 and PM6. There were
interviews made also to the other UPM paper mill’s experts of condition monitoring. From these
interviews the best ideas were selected to develop during this study. As a result a background
monitoring schemas were created to the PM4 press section and PM6 reel to monitor on-line for
example the motion times of the press section and the reel. Other examples of the monitoring
targets are to monitor the ratio between the controller output and measured variable and to
monitor the single variables.