Näytä suppeat kuvailutiedot

Sementin vaikutus lujuushajontaan

Taipalus, Heikki (2016)

dc.contributor.authorTaipalus, Heikki-
dc.date.accessioned2016-11-30T10:52:54Z
dc.date.available2016-11-30T10:52:54Z
dc.date.issued2016-
dc.identifier.uriURN:NBN:fi:amk-2016113018276-
dc.identifier.urihttp://www.theseus.fi/handle/10024/118603
dc.description.abstractTämän insinöörityön aiheena oli selvittää, paljonko sementin laadunvaihtelun osuus on betonin lujuushajonnasta ja kummalla tutkittavalla sementillä hajonta on suurempi. Tutkittavina sementteinä oli Finnsementin Rapid- ja Yleissementti. Testauspaikkana oli Ruduksen Konalan betonitehdas ja laboratorio. Testausaika oli noin neljä kuukautta. Betonin lujuudet testattiin prisma- ja puristuskokein. Betonista mitattiin myös painumaa, vesi-sementtisuhdetta ja vesimäärää sekä tarkkailtiin valmistuksen laatua. Prismalujuuksien tulosten tarkastelussa sementin valmistajan mittaamat tulokset olivat varsinkin Rapid-sementillä merkittävästi tehtaalla mitattuja tuloksia parempia. Betonin puristuskokeissa Rapidsementillä lujuustulosten keskihajonta oli suurempi kuin Yleissementin. Vesimäärän mittailussa vertailtiin wokkipannulla ja mikroaaltouunilla kuumentamalla saatuja tuloksia reseptivesimäärään. Mikroaaltouuni antoi suurimman virheen ja keskihajonta oli suurin. Mikroaaltouunilla oli myös huonoin korrelaatio reseptivesimäärään. Mikroaaltouuni antoi kuitenkin parhaan korrelaation lujuuteen ja painumaan, mutta molempien menetelmien osalta korrelaatio jäi heikoksi. Valmistuksen laadun tarkkailussa sementtikomponenteissa ei ollut vaihtelua Rapid- eikä Yleissementillä. Lujuustuloksissa Rapidsementin lujuustulokset kasvoivat hieman. Prismalujuuksien ja betonin puristuskokeiden perusteella Rapidsementillä oli suurempi vaikutus lujuushajontaan kuin Yleissementillä.fi
dc.description.abstractThe subject of this engineering thesis was to examine the proportion of cement quality vari-ation in the strength variance of concrete and to determine which of the two cement qualities studied would have the higher variance in strength variance. The two cements examined were Finnsementti’s Rapid- and Yleissementti. The testing place was Rudus Konala con-crete factory and laboratory. The testing time was about 4 months. The strengths were tested with prism and compression experiments. Concrete was also measured for water quantity and for water-cement ratio, and the quality of the manufacturing process was also under observation. Reviewing the results of prism strengths, especially those for Rapidsementti’s cement, the manufacturer’s results were significantly better than those of the factories. Rapidsementti’s standard deviation of strength results was larger than that of Yleissementti’s. Water quantity was measured by heating the samples with wok and microwave oven, and results were compared with the water content of the formula. Microwave oven gave the larg-est error and standard deviation. The correlation between the results of the microwave heat-ing test and the water quantity of the formula was the poorest. On the other hand, the mi-crowave heating test results showed the best correlation with strength and indentation re-sults. But the correlation between strength and indentation remained poor in both methods. Monitoring quality of manufacturing, cement components showed no variation in Rapid- nor Yleissementti. Rapidsementti’s strength results grew slightly. On the basis of prism strength and compression results, it can be concluded that Rap-idsementti had a larger effect on the proportion of strength variance than Yleissementti.en
dc.language.isofin-
dc.publisherMetropolia Ammattikorkeakoulu-
dc.rightsAll rights reserved-
dc.titleSementin vaikutus lujuushajontaanfi
dc.type.ontasotfi=AMK-opinnäytetyö|sv=YH-examensarbete|en=Bachelor's thesis|
dc.identifier.dscollection10024/244-
dc.organizationMetropolia Ammattikorkeakoulu-
dc.contributor.organizationMetropolia Ammattikorkeakoulu-
dc.subject.keywordsementti-
dc.subject.keywordlujuushajonta-
dc.subject.keywordvesimäärä-
dc.subject.degreeprogramfi=Materiaalitekniikka|sv=Materialteknik|en=Materials Engineering|-
dc.subject.disciplineMateriaali- ja pintakäsittelytekniikan koulutusohjelma-


Tiedostot

Thumbnail

Viite kuuluu kokoelmiin:

Näytä suppeat kuvailutiedot