dc.contributor.author | Yliselä, Arto | |
dc.date.accessioned | 2013-05-13T06:02:58Z | |
dc.date.available | 2013-05-13T06:02:58Z | |
dc.date.issued | 2013 | |
dc.identifier.uri | URN:NBN:fi:amk-201305137922 | |
dc.identifier.uri | http://www.theseus.fi/handle/10024/57998 | |
dc.description.abstract | Opinnäytetyön aiheena oli nostovälineen suunnittelu NX-ohjelmalla. Työ tehtiin Wärtsilän DCV-toimitusyksikön Työkalu- ja laitesuunnittelu osastolle. Osastolla käytetään tällä hetkellä suunnitteluun I-Deas-suunnitteluohjelmaa, joka tullaan tulevaisuudessa korvaamaan NX-suunnitteluohjelmalla. Työ toteutettiin suunnittelemalla nostoväline, joka on tarkoitettu viallisen öljypumpun vaihtoon koeajosolussa. Suunnitteluun käytettiin NX-ohjelmaa, josta tehty raportti toimii ohjeena tulevaisuudessa tällä ohjelmalla tapahtuvassa suunnittelussa. Työn tarkoituksena oli myös löytää mahdolliset ongelmat ohjelman käyttöön liittyen. Tavoitteena oli myös laatia koulutussuunnitelma osaston henkilökunnalle.
Työ aloitettiin tutustumalla koeajosoluun, jossa nostovälinettä käytettäisiin. Alkutietojen ja nostolaitteelle asetettujen vaatimusten perusteellaa tehtiin nostovälineestä muutama luonnos, joiden perustellaa aloitettiin 3D-mallien tekeminen NX:llä. Valmiille nostovälineen 3D-mallille suoritettiin standardin vaatimat lujuuslaskut NX:n Advaced Simulation-ohjelmalla. Lopuksi nostovälineestä tehtiin tarvittavat piirustukset valmistusta varten sekä standardin vaatima dokumentaatio.
Työn tuloksena saatiin raportti nostovälineen suunnittelusta, jota voidaan käyttää karkeana ohjeena NX:llä suunniteltaessa. 3D-mallinnukseen liittyen ei esiintynyt ongelmia, jotka estäisivät ohjelman käyttöönoton tähän tarkoitukseen. Advanced Simulation-osion käyttöön liittyvät kysymykset vaativat vielä lisää selvittämistä ja estävät vielä tällä hetkellä ohjelman täyden käyttöönoton. Lisäksi laadittiin ehdotus osaston henkilökunnan kouluttamiseksi. | fi |
dc.description.abstract | The aim of this thesis was to design a lifting device for oil pump replacement in the test drive cell using the NX design program. The thesis was made for Wärtsilä Vaasa Delivery Centre’s Tool and Device Design department. The staff in the de-partment now uses the I-Deas-design program but in the near future NX will be replacing it. Other aims were to find out potential problems that are related to the use of NX and to make a training plan for the designers of the department.
The thesis was started by examining the test drive cell where the lifting device will be used. The next step was sketching the lifting device. Based on these sketches 3D-modeling with NX was started. When the assembly of device was ready it was analyzed for its strength by the Advanced Simulation program. The last step was the making of drawings and documents that are needed for the CE certificate.
The result of this thesis was report on the design project which can be used as a guide line in a design project with NX in the future. There were no big problems related to 3D-modelling with NX. The biggest problem was related to the use of the Advanced Simulation program which prevents the introduction of NX in full scale. A training plan for the designers of the department was also drawn up. | en |
dc.language.iso | fin | |
dc.publisher | Vaasan ammattikorkeakoulu | |
dc.rights | All rights reserved | |
dc.title | Nostovälineen suunnittelu NX-ohjelmalla | fi |
dc.type.ontasot | fi=AMK-opinnäytetyö|sv=YH-examensarbete|en=Bachelor's thesis| | |
dc.identifier.dscollection | 10024/1672 | |
dc.organization | Vaasan ammattikorkeakoulu | |
dc.subject.ysa | nostolaitteet | fi |
dc.subject.ysa | mallintaminen | fi |
dc.subject.ysa | atk-ohjelmat | fi |
dc.contributor.organization | Vaasan ammattikorkeakoulu | |
dc.subject.keyword | NX | |
dc.subject.keyword | 3D-mallinnus | |
dc.subject.keyword | FEM-mallinnus | |
dc.subject.keyword | Nostoväline | |
dc.subject.degreeprogram | fi=Konetekniikka|sv=Maskinteknik|en=Mechanical Engineering| | |
dc.subject.discipline | Kone- ja tuotantotekniikka | |